QC Inspector - Electrical
General Characteristics (Job Summary)
- Responsible for performing quality activities in accordance with quality management system established.
- Establish inspection and test plans and its record forms as per project requirements and international codes and standards.
- Responsible in implementing the company inspection Test Plan, Inspection checklist, Material System specification, Engineering Procedure and Standards as per Project Quality Contract.
- Establish Quality Procedures and review the Construction Method of Statement prior to submission for company approval.
- Ensure inspection status is controlled through efficient tools such as inspection matrix.
- Monitor the Electrical and Instrumentation field inspection and violation such as Quality Observation Report, Log Book Entry and NCR's were corrective action implemented on the site as per target date and preventive action must be observed to avoid repeating the violation.
- Monitor that IFC drawing must be used and follow on the site for the construction activity.
- Monitor that correct materials being used and all inspections required has been carried out prior, to be issued for the installation.
- Monitor proper and correct handling, storage and preservation of Equipment and materials was implemented, vendor instruction was being followed upon the delivery on the project site until pre-commissioning stage.
- Monitor and review the preparation of loop folder and the progress of loop checking was conducted.
- Monitor the construction activity that all installations and test conducted was comply the project specification requirements, code and standard requirements to avoid any rejection and punch list.
- Monitoring and ensuring that the relevant Method Statements, Inspection Test Plans and Procedures are in line with Project Quality Plan and being followed through-out the Project Life Cycle.
Roles and Responsibilities
- Managing and performing inspection of Electrical discipline.
- Generate client Requests For Inspection (RFI) where required providing sufficient notice for hold, witness and inspection points.
- Prepare / Review the following Quality procedure documents submitted by the Subcontractors such are Inspection Test Plan (ITP), Material Approval Request (MAR).
- Prepare / Review / Approve the related inspection reports where inspection results are recorded.
- Controlling inspection status by using systematic tools such as inspection matrix.
- Setting and applying practical inspection process of particular discipline based on Project requirements and International Codes (providing ITP and managing Matrix).
- Control NCRs to be closed out within the due date and supporting to prepare Corrective Action Plan properly.
- Performing and coordinating inspection with client.
- Carry out QC Supervisor’s responsibility in their absence.
- Control quality violations through regular tool box talk with the construction team.
- Review and track material submittals required for Electrical Definable Features of Work prior to Preparatory Meetings.
- Conduct Preparatory Meetings with Subcontractors related to Electrical Definable Features of Work.
- Inspect incoming material deliveries by confirming specifications and compliance with approved submittals, conduct visual and measurement tests in conjunction with the onsite logistics team.
- Reject and facilitate the return of unacceptable materials.
- Ensure to apply lessons learnt and proper preventive action conducted.
- Prepare and review Energization Package and Motor Solo Run Packages prior to submit for company approval.
- Inspection/witness in testing and functional of Switchgear, Control gear, Power Transformer and Dry Type Transformer with client.
- Inspection/witness of MV power cable termination/splicing and testing with client.
- Witness in Motor no load test with client.
- Inspection/witness the installation and testing for Cathodic Protection system, Heat tracing Fire alarm, Telecommunication system with client.
Work location is Fadhili, Saudi Arabia.
Qualifications
Key Requirement
- Aramco experience is needed.
- Additionally, with CBT Pass is preferred for QC inspector
- If you have SAP No. and pass the CBT, please mention it in your CV.
Education and Experience
- Inspector shall be a High School graduate, or higher; shall be fully conversant with applicable Industry Standards and Specifications; and shall perform a variety of inspection functions with minimal supervision.
- Overall experience of 5 years
- Experience in Inspection Specialty : 3 years
- Experience in Contract Scope of Work : 2 years
- Inspector shall demonstrate a thorough working knowledge of the National Electric Code/NFPA 70, IEC or equivalent standards.
- The incumbent shall also have working knowledge of electrical installations including materials, methods, specifications, and hazardous location identification for oil and gas or petrochemical industries.
- Inspector should have two (2) years documented experience in the field of cathodic protection for the required specific application.
- The candidate shall be able to demonstrate a thorough working knowledge of international codes and standards related to inspecting Cathodic Protection System and its components, such as anode installation, cable installation, and positive and negative cable hookups to rectifier.
- The candidate shall be able to interpret and assess cathodic protection design packages to ensure compliance with the contractual requirements.
Knowledge
- Technical knowledge and familiar with related international codes and standards in particular discipline.
- Able to check that suitable and appropriate inspection and test tools are used.
- Investigative and analyze nonconformities and observations and figuring out solutions.
- Capability of planning and controlling inspections for medium and Mega scale project.
Job Specific Specialty
- ITP Study
- Prevention and solving inconsistency
- Pre-Inspection
- RFI Management
- Punch Clear Management
- Punch Clear Implementation
- Plant Start-Up
- Operation
- Maintenance
- Final Handover
Technical Skills / Competencies
- Cooling Tower
- Compressor Area
- Tank Farm
- Utility and Process Area
- Reactor and Reformer Area
- Flare area
- 230 KV GIS Substation
- 34.5 KV GIS Substation
- MV and LV Substation
- Central Control Building
- Remote Interface Building
- Emergency Diesel Generator
- Client Management
- Communication
- Work Proficiency
- Problem solving
- Documentation Control
- Technical Know-how
- Decision Making
- Reports preparation
Additional Information
Our benefits include
- Accommodation
- Transportation
- Flight Tickets
- Medical Insurance
Samsung E&A follows fair and merit-based recruitment practices. We do not charge any fees during the recruitment process.